What are your beliefs on A Step-by-Step Guide to Installing a Bathtub?
Mounting a bath tub isn't exactly rocket science, yet it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably hard task. If the old bathtub is conveniently easily accessible, the task can relocate easily; if you have to open up a wall to remove the old tub and also place the brand-new bathtub, the task is much harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old tub and set in the new one. Ensure you have actually qualified yourself for the job and are comfortable attempting it. Instead of employing a contractor to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This short article will assist you set up a new bathtub in your restroom if you have actually currently acquired a brand-new bathtub as well as don't need to change the setup of your previous water system pipelines.
Your devices as well as material list need to consist of the following:
Preparing for the Installation
Firstly, the supporting structure provided with the bathroom must be fitted (if needed) according to the maker's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to see to it that if the faucet features a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets unit to stop stress on the tub.
Fit the flexible faucet ports to the bottom of the two faucets using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you should do is detach the water supply. After doing so, switch on the taps to drain any kind of water staying in the system. The procedure of removing the existing faucets can be quite problematic because of the restricted gain access to that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have actually been gotten rid of, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Making use of the two wood boards under its feet, position the bathtub in the required placement. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four little factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the spirit level reads level.
To set up taps, fit the bottom of the furthest versatile faucet port to the proper supply pipe by making a compression join; then do the same for the other tap.
Activate the water and also examine all joints as well as brand-new pipework for leaks and tighten them if necessary. Fill the bath tub as well as additionally inspect the overflow outlet and also the regular outlet for leakages.
Lastly, repair the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the tub should wait until the bath tub has actually been utilized at least when as this will certainly settle it into its last setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin guaranteeing that the washing machines remain in place in between the faucet and the sink. Safeguard the tap in position with the producer provided backnut. As soon as the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet ports. The previous type should be attached to the tap finishes initially, tightening up only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bathroom meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture an inflexible seal, triggering the water to pass through the wall surface between the bathroom and the tiling, bring about complications with dampness and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and also cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the tub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealer can crack relatively early if you do not take into consideration this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently available on the market. It is a good idea to fit the floor tiles making use of water-resistant or water resistant glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading about How to Install a Bathtub? Leave a remark directly below. We'd be pleased to listen to your insights about this piece. We are looking forward that you come back again in the near future. Be sure to take the time to distribute this content if you enjoyed reading it. Thank you for going through it.
Free Estimate